Timers and RTCs
Timers and Real-Time Clocks (RTCs) are electronic devices that are used to measure time or keep track of the current time. They can be found in a wide range of applications, including computers, phones, and appliances. Timers are used to trigger an action after a specific period of time has elapsed. They can be used to control the duration of an event, or to schedule tasks to be performed at a later time. RTCs, on the other hand, are used to maintain accurate time even when the device is powered off. They are often used in devices that need to keep track of the current time and date, such as alarm clocks and smart thermostats. If you're looking for high-quality timers and RTCs for your electronic projects, you should check out Flux.ai. They have the world's largest community-driven public library of timers and RTCs, with footprints, symbols, datasheets, and simulation models. This makes it easy for you to find the components you need for your project, and ensures that you have access to accurate and up-to-date information about each component. Whether you're a professional engineer or a hobbyist, Flux.ai has the resources you need to get your project off the ground.
TPS259474LRPWR
IC SURGE STOPPER 2.7V~23V VQFN-10-HR(2x2) The TPS25947xx family of eFuses is a highly integrated circuit protection and power management solution in a small package. The devices provide multiple protection modes using very few external components and are a robust defense against overloads, short-circuits, voltage surges, reverse polarity and excessive inrush current. With integrated back-to-back FETs, reverse current flow from output to input is blocked at all times, making the devices an excellent choice for power MUX/ORing applications as well as systems which need load side energy hold up storage in case input power supply fails. The devices use linear ORing based scheme to establish an almost zero DC reverse current and emulate ideal diode behavior with minimum forward voltage drop and power dissipation. Output slew rate and inrush current can be adjusted using an external capacitor. Loads are protected from input overvoltage conditions either by clamping the output to a safe fixed maximum voltage (pin selectable), or by cutting off the output if input exceeds an adjustable overvoltage threshold. The devices respond to output overload by actively limiting the current or breaking the circuit. The output current limit threshold as well as the transient overcurrent blanking timer are user adjustable. The current limit control pin also functions as an analog load current monitor. The devices are available in a 2mm × 2mm, 10- pin HotRod™ QFN package for improved thermal performance and reduced system footprint. The devices are characterized for operation over a junction temperature range from –40°C to +125°C. • Wide operating input voltage range: 2.7V to 23V – 28V absolute maximum – Withstands negative voltages up to –15V • Integrated back-to-back FETs with low onresistance: RON = 28.3mΩ (typical) • Ideal diode operation with true reverse-current blocking • Fast overvoltage protection – Overvoltage clamp (OVC) with pin-selectable threshold (3.8V, 5.7V, 13.8V) and 5μs (typical) response time OR – Adjustable overvoltage lockout (OVLO) with 1.2μs (typical) response time • Overcurrent protection with load current monitor output (ILM) – Active current limit OR circuit-breaker options – Adjustable threshold (ILIM) 0.5A to 6A • ±10% accuracy for ILIM > 1A – Adjustable transient blanking timer (ITIMER) to allow peak currents up to 2 × ILIM – Output load current monitor accuracy: ±6% (IOUT ≥ 1A) • Fast-trip response for short-circuit protection – 500ns (typical) response time – Adjustable (2 × ILIM) and fixed thresholds • Active high enable input with adjustable undervoltage lockout threshold (UVLO) • Adjustable output slew rate control (dVdt) • Overtemperature protection • Digital outputs – Priority power MUX control (AUXOFF) and fault indication (FLT) or – Power Good indication (PG) with adjustable threshold (PGTH) • UL 2367 recognition – File No. E339631 – RILM ≥ 750Ω • IEC 62368-1 CB certified • Small footprint: QFN 2mm × 2mm, 0.45mm pitch #CommonPartsLibrary #IntegratedCircuit #PowerManagement
612 Uses0 Stars
ABS07-32.768KHZ-T
32.768 kHz SMD Crystal – The Abracon ABS07-32.768KHZ-T is a tuning-fork crystal used for real-time clocks (RTC), low-power timers, and timekeeping circuits. It operates at 32.768 kHz with ±20 ppm frequency tolerance, 12.5 pF load capacitance, and 70 kΩ maximum equivalent series resistance (ESR). It features a compact 3.2 × 1.5 × 0.9 mm, 2-pad SMD package and operates over −40°C to +85°C. #Abracon #ABS07 #32768kHz #SMDCrystal #RTC #TimingComponent #FrequencyReference #PCBDesign
1 Uses0 StarsNE555P
555 Type, Timer/Oscillator (Single) IC 100kHz 8-PDIP NE555 DIP-8 through hole The NE555P is a classic and widely used precision timer IC manufactured by companies like Texas Instruments and others. It belongs to the popular 555 timer family and is designed for generating accurate time delays, oscillations, and pulse signals. The “P” variant refers to the PDIP (Plastic Dual In-line Package), making it ideal for through-hole mounting, breadboarding, and prototyping. NE555P PDIP-8 timer Internally, the NE555P consists of: Two comparators A flip-flop A discharge transistor A voltage divider network These blocks allow flexible configuration for timing and waveform generation. Key Features Timing & Operation Modes Monostable mode (one-shot pulse generation) Astable mode (continuous oscillator) Bistable mode (flip-flop operation) Electrical Characteristics Supply voltage range: 4.5V to 16V Output can source or sink up to 200 mA Adjustable duty cycle Performance High timing accuracy and stability Timing range from microseconds to hours (depends on external R and C) Temperature-stable operation Package & Usability 8-pin DIP (through-hole) package Easy to use for: Breadboards DIY electronics Educational projects Common Applications LED flashers and blinkers Pulse generation Time delay circuits PWM control (e.g., dimming LEDs, motor speed control) Tone/sound generation #Timer #commonpartslibrary
2.4k Uses0 StarsSTM32WL33KBV7
Sub-GHz Wireless Microcontroller SoC – Arm Cortex-M0+ microcontroller with integrated sub-GHz RF transceiver for low-power wireless applications. The STMicroelectronics STM32WL33KBV7 operates at up to 64 MHz with 128 KB Flash and 32 KB SRAM, supporting RF operation in the 413–479 MHz and 826–958 MHz bands. It supports 2(G)FSK, 4(G)FSK, ASK/OOK, D-BPSK, and DSSS modulation, data rates up to 600 kbps, and programmable transmit power up to +20 dBm. Interfaces include I²C, SPI, UART/USART, GPIO, and integrated peripherals including a 12-bit 8-channel ADC, DAC, RTC, timers, AES-128, and RNG. Supply voltage is 1.7–3.6 V, with operation from −40°C to +105°C, in a 32-pin VFQFPN 5 × 5 mm package. #STMicroelectronics #STM32WL33KBV7 #STM32 #WirelessMCU #SubGHz #RFTransceiver #CortexM0 #LPWAN #IoT #EmbeddedSystems
6 Uses0 StarsTPS3436CFDBEDDFRQ1
Supervisor Open Drain or Open Collector 1 Channel TSOT-23-8 TPS3436CFDBEDDFRQ1 – Automotive precision window watchdog timer that monitors system operation by supervising watchdog timing and asserting a reset output when timing faults occur. It operates from a 1.04 V to 6.0 V supply, draws 250 nA typical quiescent current, supports factory-programmed or user-programmable watchdog timeout and reset delay, and provides active-low open-drain or push-pull outputs with watchdog enable/disable, startup delay, manual reset, and latched output options. #TexasInstruments #TPS3436CFDBEDDFRQ1 #WatchdogTimer #WindowWatchdog #AutomotiveIC #VoltageSupervisor #ResetSupervisor #NanoPower #EmbeddedSystems #PCBComponents
23 Uses0 StarsTPS259830ONRGER
Integrated Automotive eFuse with Hot-Swap Controller – Automotive-grade integrated electronic fuse (eFuse) and hot-swap controller for power distribution, automotive ECUs, ADAS, industrial automation, servers, SSDs, and embedded power management. Operates from a 2.7 V to 26 V input supply (30 V absolute maximum) and integrates a 2.7 mΩ MOSFET capable of supporting up to 20 A load current with an adjustable current limit from 2 A to 20 A. Features 1.5% accurate load current monitoring, programmable inrush current control, adjustable overvoltage protection (OVP), undervoltage protection (UVP), reverse current blocking with external blocking FET drive, thermal shutdown, short-circuit protection, fault timer, auto-retry or latch-off fault response, and power-good/fault reporting for robust system protection. Specified for operation over a −40°C to +125°C temperature range and housed in a compact 24-pin VQFN (4 × 4 mm) package. #TexasInstruments #TPS259830ONRGER #TPS25983 #eFuse #HotSwapController #PowerManagement #CurrentMonitoring #InrushControl #CircuitProtection #AutomotiveElectronics #VQFN24 #EmbeddedSystems
96 Uses0 StarsBQ25792RQMR
Charger IC Lithium Ion/Polymer 29-VQFN-HR (4x4) The BQ25792 is a switch-mode synchronous buck-boost charger with full power-path management. It can automatically regulate power flow between the input source, system load, and battery. It supports a wide input range and is designed for USB Type-C™ / USB Power Delivery (USB-PD) systems, enabling both charging and OTG (power output from battery) operation. ⭐ Key Features ⚡ High-performance charging Up to 5 A charge current Supports 1S to 4S battery packs High efficiency (up to ~96% under typical conditions) Programmable switching frequency: 750 kHz or 1.5 MHz 🔋 Wide input support Input voltage range: 3.6 V to 24 V Absolute max rating up to 30 V Supports USB adapters and barrel jack sources Detects USB charging standards (BC1.2, DCP, CDP, HVDCP, etc.) 🔄 Buck-boost power conversion Seamless buck, boost, and buck-boost operation Maintains stable system voltage even when battery is low or input varies 🔌 USB-PD / OTG support USB Power Delivery (PD 3.0 compatible) Supports OTG output (battery powers USB port) OTG voltage range: 2.8 V to 22 V 🧠 Intelligent power management NVDC power path management (system can run without battery) Dual-input power mux controller (select between two power sources) Battery supplement mode (prevents input overload) 📊 Monitoring & control Integrated 16-bit ADC for voltage, current, temperature monitoring Fully I²C configurable Autonomous or host-controlled operation 🛡️ Protection & safety Input and battery over-voltage/over-current protection Thermal regulation and shutdown Charging safety timer MOSFET protection (internal switching FETs included) 📦 Package 29-pin VQFN (4 mm × 4 mm) package Industrial temperature range: -40°C to 85°C #CommonPartsLibrary #IntegratedCircuit #PowerManagement #Battery-charger
51 Uses0 StarsR7KA8T2LFLCAC#UC0
ARM Microcontrollers - MCU RA8T2 Dual core CM85 and CM33, MRAM 1MB / RAM 2MB, w/ EtherCAT BGA289, Microcontroller with a 250 MHz Arm® Cortex®-M85 core for embedded control and real-time applications. Features up to 2 MB Flash, 1 MB SRAM, 10/100 Ethernet MAC, USB 2.0 High-Speed, CAN FD, I²C, SPI, UART, 12-bit ADC, and advanced timer peripherals for motor control and industrial applications. #Microcontroller #ArmCortexM85 #RA8T2 #Renesas #MotorControl #Ethernet #USBHS #CANFD #I2C
1 Uses0 Stars
