Switches
A switch is a device that allows electricity to flow through a circuit by completing or interrupting the connection. It is a common component in electrical and electronic systems and is used in a variety of applications, such as controlling the flow of electricity in a circuit, turning devices on and off, and routing electrical signals. One of the primary use cases for switches is to control the flow of electricity in a circuit. This can be done by manually flipping the switch or by using a control mechanism, such as a timer or a sensor. Another common use for switches is to turn devices on and off. This can be done using a switch that is built into the device or by using a separate switch that is connected to the device. In addition to these basic use cases, switches can also be used to route electrical signals. For example, a switch can be used to route a signal from one device to another or to direct a signal to a specific circuit or component. If you're looking for a wide variety of switches for your projects, flux.ai has the world's largest community-driven public library of them. The library includes footprints, symbols, datasheets, and simulation models for a wide range of switches, making it easy to find the right switch for your needs.
7447714150
Power Inductor for energy storage and filtering in DC-DC power converters. It provides 15 µH inductance, 5.5 A rated current, 6.2 A saturation current, 34.5 mΩ DC resistance (typ.), and features a magnetically shielded SMD construction for high-frequency switching applications. #PowerInductor #ShieldedInductor #Inductor #SMDPowerInductor #15uH #5.5A #DCDCConverter #WurthElektronik
6 Uses0 StarsLM5013-Q1
6-V to 100-V input, 3.5-A non-synchronous buck DC/DC converter with ultra-low quiescent current (IQ) Buck regulator, automotive-qualified synchronous step-down DC/DC converter with an input voltage range of 3.5 V to 100 V, delivering up to 3 A output current. Features an ultralow 9 µA quiescent current, 300 kHz to 2.2 MHz adjustable switching frequency with synchronization support, integrated high-side and low-side MOSFETs, and includes programmable soft-start, power-good output, enable input, and protection against undervoltage, overcurrent, overtemperature, and input transients. #BuckRegulator #StepDownConverter #DCDCConverter #Automotive #AECQ100 #3A #100V #SynchronousBuck #PowerManagement #TexasInstruments #LM5013Q1
3 Uses0 StarsTPS25751DREFR
USB Type-C/PD 3.0 controller PMIC in 38-pin WQFN (REF0038A, 4 mm x 6 mm). Texas Instruments TPS25751DREFR provides USB-C port control, USB PD policy/PHY support, I2C host/target interfaces, integrated PP5V/VBUS/PPHV power-path switching, CC/VCONN support, GPIO/ADC configuration pins, and 3.3 V core/I/O supply operation. Key grouped physical pins: PPHV pins 20/21/22, VBUS_IN pins 23/24/25, VBUS pins 32/33, PP5V pins 34/35, exposed pad 39 GND, and exposed pad 40 DRAIN.
2 Uses0 StarsPTV09A-4020F-B104
Rotary Potentiometer – 100 kΩ single-turn linear carbon potentiometer for manual analog control and user interface adjustment. Features a 9 mm body, 280° mechanical rotation, top adjustment, through-hole snap-in PCB mounting, and 20 mm flatted shaft. Rated for 0.05 W (1/20 W) power dissipation, ±20% resistance tolerance, and includes PC pin terminals with board locks for secure mounting. Designed without an integrated switch and specified for operation over a −10°C to +50°C temperature range with a 10,000-cycle mechanical life. #Bourns #PTV09A4020FB104 #RotaryPotentiometer #Potentiometer #VariableResistor #100kOhm #LinearTaper #CarbonPotentiometer #ThroughHole #UserInterface #AnalogControl #EmbeddedSystems
5 Uses0 StarsBTG7003A1EPWXUMA1
Automotive Smart High-Side Power Switch – Single-channel N-channel smart high-side power switch for automotive power distribution and wire harness protection. Operates from a 4.1 V to 28 V supply (2.75 V minimum during cranking), supports a 15.7 A nominal load current, and features an ultra-low 3.6 mΩ typical RDS(on). Includes adjustable overcurrent protection (24 A to 137.5 A), integrated I²t wire protection, analog current sensing, open-load detection (ON/OFF state), short-circuit protection, reverse battery protection, overvoltage protection, undervoltage lockout (UVLO), overtemperature protection, slew-rate control, and logic-level control input. Qualified to AEC-Q100 and ISO 26262-compliant, it operates over a −40°C to +150°C junction temperature range and is housed in a 14-pin PG-TSDSO exposed-pad package. #Infineon #BTG7003A1EPWXUMA1 #PROFET #HighSideSwitch #SmartPowerSwitch #Automotive #PowerDistribution #LoadDriver #CurrentSense #WireProtection #AECQ100 #ISO26262 #EmbeddedSystems
6 Uses0 StarsLMR51420XDDCR
Synchronous Buck DC-DC Converter – 2 A synchronous step-down (buck) switching regulator for high-efficiency power conversion in industrial, automotive, and embedded applications. Operates from a 4.5 V to 36 V input voltage, provides an adjustable output voltage from 0.6 V to 34.2 V, and switches at a 500 kHz fixed frequency. Features 40 µA typical quiescent current, 100% duty-cycle operation, synchronous rectification, cycle-by-cycle current limiting, hiccup short-circuit protection, thermal shutdown, undervoltage lockout (UVLO), power-good output, and enable input. Operates over a −40°C to +150°C junction temperature range and is housed in a 6-pin SOT-23-THIN (DDC) package. #TexasInstruments #LMR51420 #LMR51420XDDCR #BuckConverter #DCDCConverter #SynchronousBuck #SwitchingRegulator #PowerManagement #2A #SIMPLESWITCHER #SOT236 #EmbeddedSystems
1 Uses0 Stars
