Switches

Electronic Fuse Regulator 5.3A 20-WQFN (3x4) The TPS25940LRVCR is a compact eFuse (electronic fuse) power management IC from Texas Instruments designed to provide advanced power-path protection and load management for systems such as SSDs, servers, storage devices, and embedded electronics. It integrates protection features like overcurrent limiting, reverse current blocking, overvoltage protection, and controlled startup sequencing into a single chip. Wide input voltage range: 2.7 V to 18 V Adjustable current limit: 0.6 A to 5.3 A Low ON resistance: 42 mΩ typical True reverse current blocking using back-to-back MOSFETs Programmable output slew rate (dV/dt control) for inrush current management Overvoltage and undervoltage protection Fault and Power-Good outputs for system monitoring Current monitor (IMON) output Low-power DevSleep support for SSD applications Fast reverse voltage shutdown (~1 µs) Operating temperature: −40°C to +125°C junction temperature Available in a compact 20-pin WQFN package Typical Applications PCIe / SATA / SAS SSDs and HDDs Enterprise servers and storage systems RAID controller cards Smart load switches Set-top boxes and gaming systems Backup power and holdup capacitor systems Component Category This component belongs to: Power Management IC (PMIC) More specifically: eFuse / Hot-swap / Load Switch IC Package Information Package type: 20-WQFN (3 mm × 4 mm) Mounting type: Surface Mount (SMD) #commonpartslibrary #integratedcircuit #powermanagement #currentregulation

Buck Switching Regulator IC Adjustable 1 Output 1000mA SOT-23-6 The LGS5145 is a step-down DC/DC regulator with internal switching, featuring SKIP control mode, which combines low quiescent current with high switching frequency to achieve high efficiency over a wide range of load currents. The SKIP mode uses a short “burst” cycle to switch the inductor current through the internal power MOSFETs, followed by a sleep cycle in which the power switch is turned off and the load current is supplied by the output capacitor. At light loads, the burst cycle is a fraction of the total cycle time, minimizing the average supply current and greatly improving efficiency at light loads. The LGS5145 has a wide input voltage range of 4.5V55V, minimizing the need for external surge suppression components.The LGS5145 features an integrated low resistance 0.6Ω high-side power MOSFET that provides at least 1A of output current capability with excellent load and line transient response. Junction temperature range from -40°C to +125°C ■ All ports are ESD protected to 3000V (HBM). ■ Wide input voltage range: 4.5V-55V ■ 600mΩ High Side Metal Oxide Semiconductor Field Effect Transistors ■ At least 1000mA continuous current output capability ■ Up to 90% efficiency ■ SKIP mode provides very high light load efficiency ■ 1.2MHz fixed operating frequency ■ Internal compensation helps reduce solution size, cost and design complexity ■ Supports capacitive start for large loads ■ Cycle-by-cycle overcurrent protection ■ Output short circuit protection ■ thermal shutdown protection ■ Available in ultra-small package SOT23-6 package #CommonPartsLibrary #IntegratedCircuit #PowerManagement #Voltage-regulator #Switching-regulator

Electronic Fuse Regulator 4A 8-WSON (2x2) The TPS259530DSGR is a compact, integrated eFuse protection device designed to provide robust power-path management for low-voltage DC systems, particularly nominal five-volt rails. It combines multiple protection and control features into a single solution, enabling safe distribution of power to downstream circuitry while minimizing the need for external components. The device supports controlled inrush current during startup, continuous current monitoring, and rapid fault response to protect both the power source and the load. Integrated protection mechanisms include overvoltage protection, undervoltage lockout, overcurrent limiting, thermal shutdown, and reverse current blocking. This makes the device well suited for applications requiring high reliability, such as embedded systems, industrial electronics, consumer devices, and communication equipment. Functional Description The device operates as a high-side protection switch using an internal MOSFET to control current flow from the input supply to the load. It monitors input voltage, output current, and internal temperature to ensure operation within safe limits. When a fault condition such as overcurrent or overvoltage is detected, the device limits or interrupts current flow to prevent damage. The integrated control loop provides smooth startup by limiting inrush current and preventing supply droop. Reverse current blocking prevents unwanted current flow from the output back to the input when the input supply is removed or drops below the output level. Electrical Characteristics The device supports operation across a wide input voltage range suitable for low-voltage DC systems, including typical five-volt rails. It features an adjustable overvoltage protection threshold aligned with five-volt system requirements, along with configurable undervoltage lockout to ensure proper system startup and shutdown behavior. The current limit is externally programmable, allowing flexibility for different load conditions. The device exhibits low on-resistance to minimize power dissipation and voltage drop during normal operation. Protection Features The TPS259530DSGR integrates multiple protection functions to enhance system robustness. Overvoltage protection prevents excessive input voltage from reaching the load. Undervoltage lockout ensures the device only operates when the input supply is within a valid range. Overcurrent protection actively limits current during fault conditions and can respond rapidly to short circuits. Thermal shutdown protects the device from overheating by disabling operation when internal temperature exceeds safe limits. Reverse current blocking prevents backflow of current, safeguarding both the source and load. Control and Interface The device includes an enable control input that allows external control of the power path. It supports configurable behavior for fault response and recovery, depending on system design. External components can be used to set thresholds such as current limit and undervoltage lockout, providing design flexibility. Status signaling allows system-level monitoring of fault conditions. Mechanical and Package Information The TPS259530DSGR is provided in a compact surface-mount package suitable for space-constrained applications. The package is optimized for thermal performance and efficient PCB layout, enabling reliable operation under varying load conditions. It is supplied in tape-and-reel format for automated assembly processes. Applications This device is intended for use in systems requiring reliable power distribution and protection. Typical applications include five-volt power rails in embedded systems, industrial control modules, consumer electronics, communication devices, and peripheral power management circuits. Summary The TPS259530DSGR offers an integrated, high-reliability solution for power path protection and management in low-voltage systems. Its combination of protection features, configurability, and compact form factor makes it a widely used choice for safeguarding five-volt supply rails in modern electronic designs. #commonpartslibrary #integratedcircuit #powermanagement

Tactile Switch SPST-NO Top Actuated Surface Mount The FSM1LP is a surface-mount tactile (momentary) switch manufactured by TE Connectivity under the ALCOSWITCH series. It is a low-profile, top-actuated pushbutton switch designed for compact PCB applications requiring reliable user input. This switch operates as a momentary SPST-NO (Single Pole Single Throw – Normally Open) device, meaning it only conducts when pressed and returns to open when released. Key Features Switch Type Tactile momentary (OFF–(ON)) pushbutton Contact Configuration SPST-NO (Normally Open) Mounting Type Surface Mount (SMD) with gull-wing leads Actuation Style Top-actuated round button Electrical Rating 50 mA @ 24 VDC Operating Force Approximately 1.57 N (~160 gf) Low Profile Design Compact height (~3–3.5 mm typical), suitable for slim devices Mechanical Life Around 100,000 cycles Contact Material Copper alloy with silver plating for reliable conductivity Compact Size Typically ~6 × 6 mm footprint RoHS Compliant Lead-free and environmentally compliant tactile switch momentary 4 pin smd #CommonPartsLibrary #Switch

Dip Switch SPST 2 Position Surface Mount Slide (Standard) Actuator 25mA 24VDC The 218-2LPSTJ is a two-position pluggable terminal block connector designed for secure wire-to-board connections in industrial and commercial electronic applications. It features a screw-clamp termination mechanism, allowing reliable and reusable connections for solid or stranded wires. The connector is typically used in power distribution, control systems, and signal wiring where ease of maintenance and field wiring is required. Key Features Pluggable terminal block, two positions Screw-clamp wire termination for secure connection Standard pitch suitable for common PCB layouts Removable plug for easy installation and maintenance Designed for solid and stranded wire compatibility High reliability for industrial environments Mechanical Specifications Number of Positions: 2 Pitch: 5.08 mm Mounting Type: Through-hole (header) with mating plug Wire Entry: Side entry Wire Gauge Range: Typically 24 AWG to 12 AWG (manufacturer dependent) Housing Material: High-temperature thermoplastic Color: Typically green Electrical Specifications Rated Voltage: Up to 300 V (UL rating typical) Rated Current: Up to 10–15 A (depending on wire size and conditions) Contact Resistance: Low resistance, suitable for power and signal transmission Insulation Resistance: High insulation resistance under standard conditions Environmental Specifications Operating Temperature Range: −40°C to +105°C (typical) Flammability Rating: UL94 V-0 RoHS Compliant: Yes Applications Power supply connections Industrial control systems HVAC equipment Automation and instrumentation PCB-based terminal interfaces Mating / Compatibility Compatible with corresponding 2-position pluggable terminal block headers with 5.08 mm pitch Designed for repeated mating cycles without degradation #commonpartslibrary #switch #dip #spst

Tactile Switch SPST-NO Top Actuated Surface Mount The B3FS-1002P is a compact, surface-mount tactile switch designed for low-profile input applications. It provides a momentary contact mechanism with a distinct tactile feedback, making it suitable for user interface controls in consumer electronics, industrial devices, and compact embedded systems. The switch features a sealed construction for improved reliability and is optimized for automated PCB assembly processes. Mechanical Characteristics Mounting Type: Surface Mount (SMD) Actuator Style: Top push Actuator Height: Low profile Outline: Rectangular compact body Terminal Type: Gull-wing terminals Sealing: Dust-resistant (sealed construction) Electrical Characteristics Switch Type: Single Pole Single Throw (SPST) Contact Configuration: Normally Open (NO) Rated Voltage: Low voltage DC applications Rated Current: Suitable for signal-level switching Contact Resistance: Low initial contact resistance Insulation Resistance: High insulation resistance between terminals Operating Characteristics Operating Force: Standard tactile force (manufacturer-defined variant) Travel Distance: Short stroke tactile action Operating Life: High durability for repeated actuation cycles Bounce Time: Minimal contact bounce for reliable switching Environmental Characteristics Operating Temperature Range: Wide operating range suitable for consumer and industrial use Storage Temperature Range: Standard electronic component storage conditions Humidity Resistance: Designed to withstand typical ambient humidity conditions Material & Construction Actuator Material: High-strength polymer Housing Material: Heat-resistant plastic Contact Material: Metal alloy with surface plating for durability Terminal Finish: Solderable finish compatible with reflow soldering Packaging Information Packaging Type: Tape and reel Assembly Compatibility: Fully compatible with automated pick-and-place and reflow processes Applications Consumer electronics (keypads, remote controls) Industrial control panels Portable devices Embedded system user interfaces Wearable and compact electronics #commonpartslibrary #switch #tactile

USB Controller USB 2.0 I2C Interface 24-QFN (4x4) The STUSB4500QTR is a standalone USB Type-C Power Delivery (PD) controller from STMicroelectronics designed for power sink applications (devices that receive power, like chargers, IoT devices, or battery-powered systems). It enables automatic negotiation of USB Power Delivery contracts (up to 100 W: 20 V / 5 A) without requiring an external microcontroller, thanks to its built-in auto-run algorithm. Power profiles (PDOs) can be pre-configured and stored in internal non-volatile memory, simplifying system design and reducing component count. The device is optimized for modern USB-C designs, offering robust protection, high-voltage tolerance, and support for operation even from a dead battery state. Key Features Power Delivery & Control Standalone USB Type-C™ and USB PD sink controller Supports up to 100 W (20 V, 5 A) power negotiation Auto-run mode (no MCU required) for PD negotiation Up to 3 configurable sink PDO profiles stored in NVM Power Management Dead battery mode support (can start with no battery power) Dual power supply inputs: V_SYS: 3.0 V – 5.5 V V_DD: 4.1 V – 22 V Integrated VBUS monitoring and control Integrated Functions Built-in VBUS switch gate drivers (PMOS) Internal/external VBUS discharge paths I²C interface for configuration and monitoring Protection & Reliability Short-to-VBUS protection on CC pins (up to 22 V) High-voltage tolerance: Up to 28 V on VBUS pins ESD protection: 3 kV HBM / 1.5 kV CDM Physical & Environmental Package: QFN-24 (4×4 mm) Operating temperature: –40°C to +105°C Industrial-grade reliability Compliance & Compatibility Certified for: USB Type-C Rev 1.2 USB PD Rev 2.0 Interoperable with USB PD 3.0 #commonpartslibrary #integratedcircuit #usbcontroller

Solid State Photo-Coupled Relay (Photorelay) SPST-NO (1 Form A) 4-SOP (0.179", 4.55mm) The G3VM-61VY3(TR05) is a single-pole, single-throw normally open (SPST-NO) solid-state relay that uses an LED input and MOSFET output to switch AC or DC loads without mechanical contacts. It provides fast, silent, and highly reliable switching in a very small surface-mount package. Key Characteristics Relay Type: Solid State Relay (Photorelay) Contact Form: SPST-NO (1 Form A) Output Type: MOSFET Load Voltage: Up to 60 V AC/DC Load Current: Up to 700 mA On-Resistance: ~2 Ω max Input Control: LED-driven (low current DC input) Isolation Voltage: ~3.75 kV (input to output) Package: SOP-4 surface-mount (compact form factor) Packaging Option: TR = Tape & Reel for automated assembly How It Works The input LED is energized with a small DC current. It activates an internal photo-coupler. This drives a pair of MOSFETs, turning the load ON or OFF. No mechanical movement → no arcing or contact wear. Key Advantages Silent operation (no clicking sound) Very long life (no mechanical parts) Fast switching speed Compact size for dense PCB layouts Low leakage and stable performance Typical Applications Semiconductor test equipment Industrial control systems Battery-powered devices Data acquisition systems Communication and measurement circuits General-purpose signal switching #CommonPartsLibrary #Relay #SSR #G3VM