LEDs

Battery Power Management IC Lithium Ion/Polymer 24-QFN (4x4) nPM1100 is an integrated Power Management IC (PMIC) with a linear-mode lithium-ion/lithium-polymer battery charger in a compact 2.1x2.1 mm WLCSP package. It has a highly efficient, dual-mode configurable output DC/DC buck regulator. nPM1100 is an extremely compact PMIC device, created for space constrained applications with a small lithium-ion or lithium-polymer battery. It is compatible with all nRF52 and nRF53 Series SoCs and supports charging batteries at up to 500 mA through USB, and also delivers up to 150 mA of current to power external components with regulated voltage. A minimum of five passive components are required for operation and the device functions without a control interface. It is the perfect companion for nRF52 and nRF53 multiprotocol SoCs in battery powered designs. Low quiescent current (IQ) extends battery life during shipping and storage with Ship mode, or in operation using auto-controlled hysteretic buck mode for high efficiency down to 1 µA loads. Charge and error indication LED drivers are built in. Charge profile limits are configurable and VBUS current limits can be fixed or auto-controlled with on-chip USB port detection. • 400 mA linear battery charger • Linear charger for lithium-ion/lithium-polymer batteries • Adjustable charge current from 20 mA to 400 mA • Selectable termination voltage of 4.1 V or 4.2 V • Automatic trickle, constant current, and constant voltage charging • Battery thermal protection • Discharge current limitation • JEITA compliant • Li-ion/Li-polymer USB battery charger with a high efficiency buck regulator • 800 nA - Typical quiescent current • 460 nA - Shipping mode quiescent current • Thermal protection • Input regulator • USB compatible current limit of 100 mA and 500 mA • 4.1 V to 6.7 V input voltage range for normal operation • 20 V overvoltage protection • Reverse current protection • 3.0 V to 5.5 V system voltage output • USB port detection supporting the following types: • SDP • CDP/DCP • 1.8 V to 3.0 V, 150 mA step-down buck regulator • Step-down buck regulator with up to 92% efficiency • Automatic transition between hysteretic and pulse width modulation (PWM) modes • Forced PWM mode for clean power operation • Pin-selectable output voltage (1.8 V, 2.1 V, 2.7 V, 3.0 V) • Soft start-up • LED drivers for charger state indication • 5 mA low side LED driver for charging indication • 5 mA low side LED driver for error indication • 2.3 V to 4.35 V battery operating input range • 2.1x2.1 mm WLCSP package • Suitable for two layer PCB design #CommonPartsLibrary #IntegratedCircuit #NordicSemiconductor #nPM1100 #PMIC #BatteryCharger #PowerManagement #LiIon #LiPolymer #BuckConverter #Wearables #IoT #WirelessSensor #LowPowerDesign #USBCharging #EmbeddedSystems #nRF52 #nRF53 #PortableElectronics

Ethernet Controller 10/100 Base-T/TX Bus Interface 80-TQFP-EP (12x12) The LAN9254-I/JRX is an EtherCAT SubDevice (slave) controller developed by Microchip Technology, designed to serve as the communication backbone for industrial automation devices participating in an EtherCAT network. The device integrates dual Ethernet physical layer transceivers directly on-chip, eliminating the need for external PHY components and simplifying the design of EtherCAT-enabled equipment such as servo drives, sensors, I/O modules, and other field devices used in real-time industrial control systems. Architecturally, the controller can operate as either a two-port or three-port node, depending on the network topology required. In its standard configuration it functions as a two-port device supporting daisy-chain connections typical of EtherCAT line topologies. When configured as a three-port device, it gains an additional management interface port that can connect to an external PHY or to another LAN9254, enabling star or tree network topologies and allowing the device to act as a branching point within a larger EtherCAT installation. Each integrated Ethernet PHY operates in full-duplex mode and supports automatic crossover detection, so the device can use either straight-through or crossover cabling without requiring manual configuration. Beyond pure protocol handling, the LAN9254 includes a substantial set of general-purpose digital input and output lines, allowing it to be used in simple field devices without requiring a separate microcontroller. For more complex applications, the device communicates with an external host processor through an integrated host bus interface that behaves like simple memory-mapped SRAM, supporting both 8-bit and 16-bit data widths along with multiple byte-ordering conventions, which makes it straightforward to interface with a wide range of microcontroller and microprocessor architectures. Internally, dual process data RAM buffers manage the exchange of real-time process data between the host application and the EtherCAT communication engine, while a dedicated interrupt line notifies the host of relevant internal events. A key feature of the device is its built-in distributed clock mechanism, which provides high-precision timing synchronization across all nodes in an EtherCAT network. This capability is essential for motion control and other applications where multiple devices must act in tight temporal coordination. The controller also provides configurable status indication through standard network activity and link LEDs, along with optional error and run-state indicators that give visibility into the health and operational state of the device at a glance. Power architecture on the LAN9254 is simplified through an integrated linear regulator, allowing the device to be operated from a single primary supply rail while internally generating the lower voltage needed for its core logic. This reduces the external power supply complexity that would otherwise be required to support separate core and I/O voltage domains. The "-I" designation on this particular part number indicates an industrial-grade temperature rating, making it suitable for deployment in factory floor and other demanding industrial environments where extended thermal range and long-term reliability are required. The device is housed in a surface-mount package consistent with dense industrial control board layouts and is compliant with RoHS material restrictions. Spec Sheet Identification Part Number: LAN9254-I/JRX Device Family: LAN9254 Manufacturer: Microchip Technology Functional Classification Device Type: EtherCAT SubDevice (slave) controller Network Role: Two/three-port configurable node Integrated PHYs: Dual Ethernet physical layer transceivers, on-chip Auto-MDIX Support: Yes, supports direct and crossover cabling Communication & Protocol Features Protocol: EtherCAT Topology Support: Daisy-chain (line), star, and tree topologies Additional Port Mode: Optional third port for branching/tap configurations Clock Synchronization: Integrated distributed clock for high-precision timing Host Interface Interface Type: SRAM-like host bus interface Data Width Support: Selectable bit-width host bus operation Endianness Support: Multiple byte-ordering modes Process Data Handling: Dual process data RAM buffers Interrupt Support: Configurable host interrupt line Digital I/O General-Purpose I/O: Integrated digital I/O lines for microcontroller-less operation Standalone Mode: Supports operation without external microcontroller for simple device designs Power Architecture Supply Configuration: Single primary supply rail Internal Regulation: Integrated linear regulator for core voltage generation Status Indication LED Support: Standard run and link/activity indicators per port Optional Indicators: Configurable error and run-state status indicators Environmental & Qualification Temperature Grade: Industrial ("-I" suffix) RoHS Compliance: Yes Package Package Type: Surface-mount, quad flat package style Mounting: Surface mount technology (SMT) Packaging Format Supply Format: Tape-and-reel, per part suffix designation #LAN9254 #Microchip #EtherCAT #SlaveController #SubDeviceController #IndustrialEthernet #IndustrialAutomation #MotionControl #EmbeddedSystems #FieldDevice #DigitalIO #HostBusInterface #DistributedClock #TQFP #RoHSCompliant #IndustrialGrade #EngineeringSpec #ComponentLibrary #CommonPartsLibrary #SemiconductorIC

Battery Multi-Function Controller IC Lithium Ion/Polymer 32-VFQFPN (5x5) L9961 is part of a complete battery pack monitoring, balancing, and protecting system for Li-Ion and Li-Polymer cells in 3, 4 or 5 series configurations. The L9961 uses a high precision ADC to provide cell voltage, stack voltage and temperature conversion via external NTC. Voltage monitoring functions are cyclically performed with a programmable loop time. Stack current is also monitored via a high accuracy CSA, continuously running and performing also Coulomb counting. Cell balancing is available and can be simultaneously activated on all cells. IC configuration and information exchange for SOC/SOH estimation are performed via I2C peripheral. The IC also integrates a dual pre-driver programmable in both HS/LS configurations for driving pack relays. L9961 also implements battery pack fuse protection to prevent fire and explosion hazards. A 3.3 V regulator with a high current capability is available for supplying pack controller and other external circuitry in both standby and normal operation modes. The IC protects the battery pack against over/under voltage conditions and monitors for over/ under temperature. It also features protection against overcurrent (both directions) and short-circuit in discharge events. Safety-relevant configurations can be stored in the internal NVM to avoid re-programming the device at each wake-up. Features • 2 μA shipment - DEEP SLEEP mode current and 5 μA standby consumption (with VREG LDO active) standby consumption (with VREG LDO active) • Integrated 3.3 V VREG LDO for supplying MCU and LEDs • Measures cell voltage (3 to 5 cells), with over/undervoltage detection and balance undervoltage protection • 12-bit voltage measurement with maximum error of ±15 mV in the [1.5 – 4.5] V range, for -40 °C < TJ < 105 °C • Measures stack voltage, with over/under voltage detection and plausibility check vs. sum of cells • Measures pack temperature via NTC, with over/undertemperature detection • Ratiometric temperature measurement with ±0.8% max. gain error in the [0.2 – VREG] V range, for -40 °C < TJ < 105 °C • Measures battery current, with Coulomb counting, overcurrent (both directions) and short-circuit in discharge protection. • 16-bit signed current measurement with 0.1% full scale error at room temperature • I 2C peripheral for device programming and data transfers over I2C bus • Cell balancing supporting up to 70 mA per cell • Dual configurable HS/LS predriver for pack relay management • Pack fuse management • Embedded NVM for configuration parameters storage • High hotplug robustness Applications • Cordless power tools • Backup energy storage systems and UPS • Light electric vehicles (e-bikes, scooters, etc.) • Portable and semi-portable equipment • Medical equipment #L9961TR #BatteryManagement #BMS #LiIonBattery #LiPoBattery #STMicroelectronics #BatteryProtection #CellBalancing #CoulombCounting #PowerManagement #EmbeddedSystems #EnergyStorage #EBike #PowerTools #ElectronicsDesign

OPSCO SK6812MINI RGBW is an intelligent addressable RGBW LED with an integrated control IC inside a compact 3.7 mm × 3.7 mm surface-mount package. It combines red, green, blue, and dedicated white LEDs with a built-in constant-current driver, allowing individual pixel control through a single-wire serial data interface. Each LED contains an internal data latch, PWM controller, signal reshaping circuit, and cascade output, enabling long chains of individually addressable LEDs without additional external components. Compatible with SK6812 and similar NeoPixel-style protocols, it is widely used in LED displays, decorative lighting, wearable electronics, smart home devices, gaming peripherals, indicators, keyboards, and embedded lighting applications. Features include serial data input/output (DIN/DOUT), integrated PWM dimming, high color consistency, and easy daisy-chain connectivity. Search Keywords: SK6812MINI, SK6812 MINI, RGBW LED, addressable RGBW LED, intelligent LED, NeoPixel compatible LED, smart RGB LED, serial controlled LED, individually addressable LED, DIN DOUT LED, programmable LED, LED pixel, embedded lighting LED, digital RGBW LED, SMD RGBW LED, LED strip pixel, SK6812 LED driver Hashtags: #SK6812MINI #SK6812 #RGBW #AddressableLED #SmartLED #NeoPixel #DigitalLED #LEDPixel #EmbeddedLighting #LEDDisplay #Arduino #ESP32 #IoT #WearableElectronics #PCBDesign #LightingControl #SMDLED #ElectronicComponents #LEDDriver #RGBLEDProgrammable LED; RGBW; SMD; 3535,PLCC4; 3.75.5VDC; 3800-4200K

Red, Green, Blue (RGB) 624nm Red, 525nm Green, 470nm Blue LED Indication - Discrete 2V Red, 3.3V Green, 3.3V Blue 4-SMD, No Lead # 150080M153000 ## General Description The 150080M153000 is a compact surface-mount full-color RGB LED manufactured by Würth Elektronik as part of the WL-SFCD series. The device integrates red, green, and blue light-emitting elements within a single package, enabling the generation of a wide spectrum of colors for status indication, user interfaces, backlighting, visual notifications, and decorative lighting applications. Its diffused lens design provides uniform light distribution and wide viewing visibility, making it suitable for industrial equipment, consumer electronics, communication devices, instrumentation systems, control panels, and embedded electronic products. The component is optimized for automated assembly processes and offers reliable optical performance, low power consumption, and long operational life. ## Key Features ### Optical Characteristics * Full-color RGB light output * Integrated red, green, and blue emitters * Diffused lens design for uniform illumination * Wide viewing angle * High-visibility indication capability * Consistent color performance ### Electrical Characteristics * Low-power operation * Stable optical output * Suitable for indicator and backlighting applications * Reliable performance across operating conditions * Optimized for embedded electronic systems ### Mechanical Characteristics * Surface-mount package construction * Compact footprint * Low-profile package design * Compatible with automated assembly processes * Reflow-soldering compatible ### Package Construction * Common-anode configuration * Integrated multi-die LED architecture * Rectangular lens geometry * Lead-free package design * Industrial-grade construction ### Material Characteristics * High-quality encapsulation materials * Diffused optical lens * RoHS-compliant construction * Environmentally compliant materials ### Environmental Characteristics * Suitable for commercial and industrial applications * Long operational service life * Reliable operation under standard environmental conditions * Resistant to normal assembly and handling processes ### Application Areas * Status Indicators * User Interface Displays * Industrial Control Panels * Consumer Electronics * Home Appliances * Telecommunications Equipment * Instrumentation Systems * Backlighting Applications * Smart Devices * Embedded Electronic Products * Safety and Security Equipment * Human-Machine Interface Systems ### Compliance * RoHS Compliant * REACH Compliant * Lead-Free Compatible * Industry-Standard Surface-Mount Technology ## Manufacturer Würth Elektronik ## Product Family WL-SFCD SMD Full-Color Chip LED Series #150080M153000 #WurthElektronik #RGBLED #SMDLED #WLSFCD #FullColorLED #LEDIndicator #Backlighting #Optoelectronics #EmbeddedSystems #IndustrialElectronics #ConsumerElectronics #PCBDesign #ElectronicsEngineering #SMTAssembly #commonpartslibrary #optoelectronic #ledindication

555 Type, Timer/Oscillator (Single) IC 100kHz 8-PDIP NE555 DIP-8 through hole The NE555P is a classic and widely used precision timer IC manufactured by companies like Texas Instruments and others. It belongs to the popular 555 timer family and is designed for generating accurate time delays, oscillations, and pulse signals. The “P” variant refers to the PDIP (Plastic Dual In-line Package), making it ideal for through-hole mounting, breadboarding, and prototyping. NE555P PDIP-8 timer Internally, the NE555P consists of: Two comparators A flip-flop A discharge transistor A voltage divider network These blocks allow flexible configuration for timing and waveform generation. Key Features Timing & Operation Modes Monostable mode (one-shot pulse generation) Astable mode (continuous oscillator) Bistable mode (flip-flop operation) Electrical Characteristics Supply voltage range: 4.5V to 16V Output can source or sink up to 200 mA Adjustable duty cycle Performance High timing accuracy and stability Timing range from microseconds to hours (depends on external R and C) Temperature-stable operation Package & Usability 8-pin DIP (through-hole) package Easy to use for: Breadboards DIY electronics Educational projects Common Applications LED flashers and blinkers Pulse generation Time delay circuits PWM control (e.g., dimming LEDs, motor speed control) Tone/sound generation #Timer #commonpartslibrary